Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

D100EI Ver la hoja de datos (PDF) - MicroPower Direct, LLC

Número de piezacomponentes DescripciónFabricante
D100EI Low Cost, 1W High Isolation SIP DC/DC Converters MPD
MicroPower Direct, LLC MPD
D100EI Datasheet PDF : 2 Pages
1 2
Model Selection Guide
Model
Number
D101EI
D102EI
D103EI
D104EI
D105EI
D106EI
D107EI
D108EI
D111EI
D112EI
D113EI
D114EI
D115EI
D116EI
D117EI
D118EI
D121EI
D122EI
D123EI
D124EI
D125EI
D126EI
D127EI
D128EI
Input
Voltage (VDC)
Current (mA)
Nominal Range Full-Load No-Load
5
4.5 - 5.5
256
30
5
4.5 - 5.5
256
30
5
4.5 - 5.5
250
30
5
4.5 - 5.5
247
30
5
4.5 - 5.5
278
30
5
4.5 - 5.5
267
30
5
4.5 - 5.5
247
30
5
4.5 - 5.5
250
30
12 10.8 - 13.2 107
15
12 10.8 - 13.2 104
15
12 10.8 - 13.2 103
15
12 10.8 - 13.2 104
15
12 10.8 - 13.2 114
15
12 10.8 - 13.2 104
15
12 10.8 - 13.2 103
15
12 10.8 - 13.2 105
15
24 21.6 - 26.4
53
8
24 21.6 - 26.4
53
8
24 21.6 - 26.4
53
8
24 21.6 - 26.4
53
8
24 21.6 - 26.4
58
8
24 21.6 - 26.4
55
8
24 21.6 - 26.4
53
8
24 21.6 - 26.4
52
8
Voltage
(VDC)
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
Output
Current
(mA, Max)
200.0
111.0
83.0
67.0
±100.0
±56.0
±42.0
±33.0
200.0
111.0
83.0
67.0
±100.0
±56.0
±42.0
±33.0
200.0
111.0
83.0
67.0
±100.0
±56.0
±42.0
±33.0
Current
(mA, Min)
20.0
12.0
9.0
7.0
±10.0
±6.0
±5.0
±4.0
20.0
12.0
9.0
7.0
±10.0
±6.0
±5.0
±4.0
20.0
12.0
9.0
7.0
±10.0
±6.0
±5.0
±4.0
Load
Regulation
(%, Max)
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
Efciency
(%, Typ)
78
78
80
81
72
78
81
80
78
80
81
80
75
80
81
79
78
79
79
79
72
78
78
80
Fuse Rating
Slow-Blow
(mA)
500
500
500
500
500
500
500
500
200
200
200
200
200
200
200
200
100
100
100
100
100
100
100
100
Notes:
1. Output load regulation is specied for a load change of 10% to 100%.
2. These units should not be operated with a load under 10% of full load.
Operation at no-load may cause damage to the unit.
3. These converters
will operate without
external compo-
nents. However,
when measuring
output ripple, it is
Vin
5 VDC
12 VDC
Input
Capacitor
4.7 μF
2.2 μF
Vout
Output Capacitor
Single Dual
5 VDC 10.0 μF 4.7 μF
9 VDC 4.7 μF 2.2 μF
recommended that
an external ceramic
capacitor be placed
24 VDC
1.0 μF 12 VDC 2.2 μF 1.0 μF
15 VDC 1.0 μF 0.47 μF
from the +Vout pin to the -Vout pin for single output units and from each
output to common for dual output units. An input capacitor will enhace sta-
bility over temperature and input line variations. Recommended capacitor
values are given in the table above. For applications requiring very low
output noise levels, a simple LC lter should be effective.
4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC
output. To do this, connect the load across the positive (+Vout) and nega-
tive (-Vout) outputs and oat the output common
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.
Derating Curve
Mechanical Dimensions
Pin Connections
Pin Single Dual
Pin
1 +Vin +Vin
6
2 -Vin -Vin
7
5 -Vout -Vout
Single
No Pin
+Vout
Dual
Common
+Vout
Notes: All dimensions are typical in inches (mm)
Tolerance x.xx = ±0.01 (±0.25)
Pin 1 is marked by a “dot” or indentation on the
side of the unit
MicroPower Direct
www.micropowerdirect.com
232 Tosca Drive Stoughton, MA 02072
TEL: (781) 344-8226
FAX: (781) 344-8481
E-Mail: sales@micropowerdirect.com
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]