DatasheetQ Logo
Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

CMP04 View Datasheet(PDF) - Analog Devices

Part Name
Description
Manufacturer
CMP04 Datasheet PDF : 8 Pages
1 2 3 4 5 6 7 8
CMP04–SPECIFICATIONS
ELECTRICAL CHARACTERISTICS (@ V+ = 5 V, TA = 25؇C, unless otherwise noted.)
Parameter
Symbol Conditions
Min Typ Max
Unit
Input Offset Voltage
VOS
Input Offset Current
IOS
Input Bias Current
IB
Voltage Gain
AV
Large Signal Response Time
tr
Small Signal Response Time
tr
Input Voltage Range
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Saturation Voltage
Output Sink Current
Output Leakage Current
Supply Current
CMVR
CMRR
PSRR
VOL
ISINK
ILEAK
I+
RS = 0 , RL = 5.1 k, VO = 1.4 V1
IIN(+) – IIN(–), RL = 5.1 k, VO = 1.4 V
IIN(+) or IIN(–)
RL 15 k, V+ = 15 V2
80
VIN = TTL Logic Swing, VREF = 1.4 V3
VRL = 5 V, RL = 5.1 k
VIN = 100 mV Step3, 5 mV Overdrive
VRL = 5 V, RL = 5.1 k
Note 4
0
Notes 2, 5
80
V+ = 5 V to 18 V2
80
VIN(–) 1 V, VIN(+) = 0, ISINK 4 mA
VIN(–) 1 V, VIN(+) = 0, VO 1.5 V
6
VIN(+) 1 V, VIN(–) = 0, VO = 30 V
RL = , All Comps V+ = 30 V
0.4 1
2
10
25
100
200
mV
nA
nA
V/mV
300
ns
1.3
µs
V+ – 1.5 V
100
dB
100
dB
250 400
mV
16
mA
0.1 100
nA
0.8 2.0
mA
NOTES
1At output switch point, VO = 1.4 V, RS = 0 with V+ from 5 V, and over the full input common-mode range (0 V to V+ – 1.5 V).
2Guaranteed by design.
3Sample tested.
4The input common-mode voltage or input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of the common-mode voltage range
is V+ – 1.5 V, but either or both inputs can go to 30 V without damage.
5RL 15 k, V+ = 15 V, VCM = 1.5 V to 13.5 V.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS1
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . +36 V or ± 18 V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . 36 V dc
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +36 V
Operating Temperature Range
CMP04FS . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
Junction Temperature (TJ) . . . . . . . . . . . . . –65°C to +150°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Input Current (VIN < –3.0 V) . . . . . . . . . . . . . . . . . . . 50 mA
Output Short Circuit to GND . . . . . . . . . . . . . . . . Continuous
Lead Temperature (Soldering, 60 sec) . . . . . . . . . . . . . 300°C
Package Type
14-Lead SOIC
JA2
JC
Unit
120
36
°C/W
NOTES
1Absolute maximum ratings apply to both DICE and packaged parts, unless
otherwise noted. Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress rating only; functional
operation of the device at these or any other conditions above those listed in the
operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
2θJA is specified for worst-case mounting conditions, i.e., θJA is specified for device
soldered to printed circuit board for SOIC package.
Model
CMP04FS
TA = 25؇C
VOS
1 mV
ORDERING GUIDE
Temperature
Ranges
–40°C to +85°C
Package
Descriptions
14-Lead SOIC
Package
Options
R-14
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the CMP04 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
–2–
REV. D
 

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]