DatasheetQ Logo
Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

AZ34063P-E1 View Datasheet(PDF) - American Accurate Components, Inc.

Part Name
Description
Manufacturer
AZ34063P-E1
AAC
American Accurate Components, Inc. AAC
AZ34063P-E1 Datasheet PDF : 13 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Data Sheet
0.8A STEP-DOWN/STEP-UP/INVERTING DC-DC CONVERTER
AZ34063
Electrical Characteristics
(VCC = 5.0 V, TA = -40 to 85oC, unless otherwise specified.)
Parameter
OSCILLATOR
Frequency
Charge Current
Discharge Current
Discharge to Charge
Current Ratio
Symbol
Conditions
Min Typ Max Unit
fOSC
VPin 5 = 0 V,
CT = 1.0 nF 24 33 42 KHz
TA = 25oC
CT = 330 pF 50 65 80 KHz
ICHG
VCC = 5.0 V to 36 V, TA = 25oC 24 35 42 PA
IDISCHG VCC = 5.0 V to 36 V, TA = 25oC 140 220 260 PA
IDISCHG/ICHG Pin 7 to VCC, TA = 25oC
5.2 6.5 7.5
Current Limit Sense
VIPK(sense) ICHG = IDISCHG, TA = 25oC
OUTPUT SWITCH (Note 3)
Saturation Voltage,
Dalington Connection
VCE(sat) ISW = 0.6 A,
Pins 1, 8 connected
Saturation Voltage (Note 4)
DC Current Gain
Collector Off-State Current
COMPARATOR
VCE(sat)
hFE
IC(off)
ISW = 0.6 A, RPin 8 = 82 : to
VCC, Forced E = 20
ISW = 0.6 A,
VCE = 5.0 V,
VCE = 36 V
Threshold Voltage
Threshold Voltage Line
Regulation
VTH
REGLINE
TA = 25oC
TA = -40 to 85oC
VCC = 3.0 V to 36 V
250 300 350 mV
1.0 1.3 V
0.45 0.8 V
50 75
0.01 100 PA
1.225 1.250 1.275 V
1.21
1.29
1.4 5 mV
Input Bias Current
TOTAL DEVICE
Supply Current
IIB
VIN = 0 V
ICC
VCC = 5.0 V to 36 V, CT = 1.0 nF,
Pin 7 = VCC, VPin 5 > VTH,
Pin 2 = GND, other pins open
-20 -400 nA
4 mA
Note 3: Low duty cycle pulse technique are used during test to maintain junction temperature as close to ambient temperature
as possible.
Note 4: If the output switch is driven into hard saturation (non-Darlington configuration) at low switch currents (d 300mA)
and high driver currents (t 30mA), it may take up to 2.0us for it to come out of saturation. This condition will shorten the off
time at frequencies 30KHz, and is magnified at high temperatures. This condition does not occur with a Darlington configura-
tion, since the output switch cannot saturate. If a non-Darlington configuration is used, the following output drive condition is
recommended:
Apr. 2005 Rev. 2. 1
BCD Semiconductor Manufacturing Limited
5
 

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]