Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits
Part Name  

APA1000-TQG144ES View Datasheet(PDF) - Actel Corporation

Part NameAPA1000-TQG144ES ACTEL
Actel Corporation ACTEL
DescriptionProASICPLUS® Flash Family FPGAs
APA1000-TQG144ES Datasheet PDF : 178 Pages
First Prev 161 162 163 164 165 166 167 168 169 170 Next Last
Datasheet Information
ProASICPLUS Flash Family FPGAs
List of Changes
The following table lists critical changes that were made in the current version of the document.
Previous version Changes in current version (v5.9)
v5.8
(June 2009)
The –F speed grade is no longer supported and was removed from the datasheet.
A note regarding RoHS compliant packages was added to the "Device Resources" table.
v5.7
The "PLL Electrical Specifications" table was updated significantly. Changes were made to the
(September 2008) Input, VCO (Voltage Controlled Oscillator), and Output frequencies, and the acquisition time.
Table 2-10 • PLL I/O Constraints is new.
Table 2-23 • DC Electrical Specifications (VDDP = 3.3 V ±0.3 V and VDD = 2.5 V ±0.2 V)
Applies to Commercial and Industrial Temperature Only is the same table that was in v5.7, but it
now only applies to commercial and industrial temperature ranges. Table 2-24 • DC Electrical
Specifications (VDDP = 3.3 V ±0.3 V and VDD = 2.5 V ±0.2 V) Applies to Military Temperature
and MIL-STD-883B Temperature Only is based on Table 2-23 but Table 2-24 only applies to
military temperature. The VOH and VOL specifications were updated in Table 2-24, and changes
have been made to the drive currents at which 3.3 V VOH and VOL voltage levels are measured
and are now split by slew rate. In addition in Table 2-24, the maximum VIL specification has
changed from 0.8 V to 0.7 V for 3.3 V Schmitt-trigger input operation.
v5.6
(August 2008)
VOH and VOL data in Table 2-24 • DC Electrical Specifications (VDDP = 3.3 V ±0.3 V and VDD =
2.5 V ±0.2 V) Applies to Military Temperature and MIL-STD-883B Temperature Only was
changed back to the data in v5.5.
v5.5
(February 2007)
VOH and VOL data was updated in Table 2-24 • DC Electrical Specifications (VDDP = 3.3 V ±0.3
V and VDD = 2.5 V ±0.2 V) Applies to Military Temperature and MIL-STD-883B Temperature
Only.
v5.4
(October 2006)
A statement about single cell and cascaded cell timing diagrams was added to the "Enclosed
Timing Diagrams – FIFO Mode:" section.
The following pins were updated in the "144-FBGA Pin" table:
Pin Number Updated Function
C2
I/O / GL1
F1
I/O / GL2
v5.3
The heading, MIL-STD-883B, and note 4 were added to the "Device Resources" table.
(May 2006)
The "Temperature Grade Offerings" table was updated to include the military (M) temperature
grade in the following device/packages:
APA300-FG144
APA300-FG256
APA600-FG256
APA600-FG484
APA600-FG676
APA1000-FG896
v5.2
90° and 270° phase shift support was removed from the datasheet.
(December 2005) The "Ordering Information" section was updated to include RoHS information.
The last paragraph of the "Boundary Scan (JTAG)" section was updated.
The Output Frequency Range in the "Timing Control and Characteristics" section.
The title for Table 2-19 • Military Temperature Grade Product Performance Retention was
updated.
The caption was updated in Figure 2-45 • FIFO Reset.
Page
N/A
iii
2-18
2-19
2-38
2-38
2-38
2-65
3-38
iii
iv
N/A
ii
2-8
2-10
2-32
2-72
v5.9
4-1
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]