DatasheetQ Logo
Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

ADV7171KSUZ-REEL View Datasheet(PDF) - Analog Devices

Part Name
Description
Manufacturer
ADV7171KSUZ-REEL Datasheet PDF : 64 Pages
First Prev 11 12 13 14 15 16 17 18 19 20 Next Last
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
ADV7170/ADV7171
44 43 42 41 40 39 38 37 36 35 34
VAA 1
P5 2
P6 3
P7 4
P8 5
P9 6
P10 7
P11 8
P12 9
GND 10
VAA 11
PIN 1
ADV7170/ADV7171
MQFP/TQFP
TOP VIEW
(Not to Scale)
33 VREF
32 DAC A
31 DAC B
30 VAA
29 GND
28 VAA
27 DAC D
26 DAC C
25 COMP
24 SDATA
23 SCLOCK
12 13 14 15 16 17 18 19 20 21 22
Figure 5. Pin Configuration
Table 9. Pin Function Descriptions
Pin No.
Mnemonic
Input/
Output
1, 11, 20, 28, 30 VAA
P
2 to 9, 12 to 14, P15 to P0
I
38 to 42
10, 19, 21, 29, 43 GND
G
15
HSYNC
I/O
16
FIELD/VSYNC I/O
17
BLANK
I/O
18
ALSB
I
22
RESET
I
23
SCLOCK
I
24
SDATA
I/O
25
COMP
O
26
DAC C
O
27
DAC D
O
31
DAC B
O
32
DAC A
O
33
VREF
I/O
34
RSET
I
Description
Power Supply (3 V to 5 V).
8-Bit 4:2:2 Multiplexed YCrCb Pixel Port (P7 to P0) or 16-Bit YCrCb Pixel Port (P15 to P0).
P0 represents the LSB.
Ground Pin.
HSYNC (Mode 1 and Mode 2) Control Signal. This pin may be configured to output (master
mode) or accept (slave mode) sync signals.
Dual Function FIELD (Mode 1) and VSYNC (Mode 2) Control Signal. This pin may be
configured to output (master mode) or accept (slave mode) these control signals.
Video Blanking Control Signal. The pixel inputs are ignored when this is Logic Level 0. This
signal is optional.
TTL Address Input. This signal sets up the LSB of the MPU address.
The input resets the on-chip timing generator and sets the ADV7170/ADV7171 into default
mode. This is NTSC operation, Timing Slave Mode 0, 8-bit operation, 2 × composite and
S-Video out, and DAC B powered on and DAC D powered off.
MPU Port Serial Interface Clock Input.
MPU Port Serial Data Input/Output.
Compensation Pin. Connect a 0.1 μF capacitor from COMP to VAA. For optimum dynamic
performance in low power mode, the value of the COMP capacitor can be lowered to as low
as 2.2 nF.
RED/S-Video C/V Analog Output.
GREEN/S-Video Y/Y Analog Output.
BLUE/Composite/U Analog Output.
PAL/NTSC Composite Video Output. Full-scale output is 180 IRE (1286 mV) for NTSC and
1300 mV for PAL.
Voltage Reference Input for DACs or Voltage Reference Output (1.235 V).
A 150 Ω resistor connected from this pin to GND is used to control full-scale amplitudes
of the video signals.
Rev. C | Page 11 of 64
 

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]