DatasheetQ Logo
Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

ADV7150LS135 View Datasheet(PDF) - Analog Devices

Part Name
Description
Manufacturer
ADV7150LS135 Datasheet PDF : 36 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
ADV7150
NOTES
1TTL input values are 0 to 3 volts, with input rise/fall times 3 ns, measured between the 10% and 90% points. ECL inputs (CLOCK, CLOCK) are
VAA–0.8 V to VAA–1.8 V, with input rise/fall times 2 ns, measured between the 10% and 90% points. Timing reference points at 50% for inputs and out-
puts. Analog output load 10 pF. Databus (D0–D9) loaded as shown in Figure 1. Digital output load for LOADOUT, PRGCKOUT, SCKOUT, I PLL and
SYNCOUT 30 pF.
2± 5% for all versions.
3Temperature range (TMIN to TMAX): 0°C to +70°C; TJ (Silicon Junction Temperature) 100°C.
4Pixel Port consists of the following inputs: Pixel Inputs: RED [A, B, C, D]; GREEN [A, B, C, D]; BLUE [A, B, C, D], Palette Selects: PS0 [A, B, C, D]; PS1
[A, B, C, D]; Pixel Controls: SYNC, BLANK; Clock Inputs: CLOCK, CLOCK, LOADIN, SCKIN; Clock Outputs: LOADOUT, PRGCKOUT, SCKOUT.
5τ is the LOADOUT Cycle Time and is a function of the Pixel CLOCK Rate and the Multiplexing Mode: 1:1 multiplexing; τ = CLOCK = t1 ns. 2:1 Multi-
plexing; τ = CLOCK × 2 = 2 × t1 ns. 4:1 Multiplexing; τ = CLOCK × 4 = 4 × t1 ns.
6These fixed values for Pipeline Delay are valid under conditions where t 10 and τ-t11 are met. If either t10 or τ-t11 are not met, the part will operate but the Pipe line De-
lay is increased by 2 additional CLOCK cycles for 2:1 Mode and is increased by 4 additional CLOCK cycles for 4:1 Mode, after calibration is performed.
7Output delay measured from the 50% point of the rising edge of CLOCK to the 50% point of full-scale transition. Output rise/fall time measured between the 10%
and 90% points of full-scale transition. Transition time measured from the 50% point of full-scale transition to the output remaining within 2% of the final output
value (Transition time does not include clock and data feedthrough).
8t23 and t24 are measured with the load circuit of Figure 1 and defined as the time required for an output to cross 0.4 V or 2.4 V.
9t25 is derived from the measured time taken by the data outputs to change by 0.5 V when loaded with the circuit of Figure 1. The measured number is then extrapo-
lated back to remove the effects of charging the 100 pF capacitor. This means that the time, t 25, quoted in the Timing Characteristics is the true value for the device
and as such is independent of external databus loading capacitances.
Specifications subject to change without notice.
CLOCK
TO
OUTPUT
PIN
100pF
ISINK
+2.1V
ISOURCE
Figure 1. Load Circuit for Databus Access and Relinquish Times
t2
t1
t3
CLOCK
t4
LOADOUT
(1:1 MULTIPLEXING)
LOADOUT
(2:1 MULTIPLEXING)
LOADOUT
(4:1 MULTIPLEXING)
LOADIN
Figure 2. LOADOUT vs. Pixel Clock Input (CLOCK, CLOCK)
t5
t6
t7
PIXEL INPUT
DATA*
t8
t9
VALID
DATA
VALID
DATA
VALID
DATA
*INCLUDES PIXEL DATA (R0–R7, G0–G7, B0–B7); PALETTE SELECT INPUTS (PS0–PS1); BLANK; SYNC
Figure 3. LOADIN vs. Pixel Input Data
–4–
REV. A
 

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]