Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

AD8004AR-14_99 データシートの表示(PDF) - Analog Devices

部品番号コンポーネント説明メーカー
AD8004AR-14_99 Quad 3000 V/ms, 35 mW Current Feedback Amplifier ADI
Analog Devices ADI
AD8004AR-14_99 Datasheet PDF : 16 Pages
First Prev 11 12 13 14 15 16
AD8004
G = +2, RF = 1.10k
+2
CL = 10pF
0
+2
G = –2, RF = 698
0
CL = 0
–2
–4
–2
–4
VIN = 50mV
–6 ؎5VS
RL = 100
–8
–6
CL = 10pF
–8
–10
CL = 0
–12
–10
–14
–12
–14
1
10
40
100
500
FREQUENCY – MHz
Figure 35. Frequency Response vs. Capacitive Loading,
RL = 100 Output
+2
0
G = +2
–2 RL = 1k
؎5VS
–4 VIN = 50mV rms
RF = 1.2k
–6
CL = 10pF
CL = 0
–8
–10
–12
–14
1
10
40
100
500
FREQUENCY – MHz
Figure 36. Flatness with 10 pF Capacitive Load
DRIVING A SINGLE-SUPPLY A/D CONVERTER
New CMOS A/D converters are placing greater demands on the
amplifiers that drive them. Higher resolutions, faster conversion
rates and input switching irregularities require superior settling
characteristics. In addition, these devices run off a single +5 V
supply and consume little power, so good single-supply operation
with low power consumption are very important. The AD8004
is well positioned for driving this new class of A/D converters.
Figure 37 shows a circuit that uses an AD8004 to drive an
AD876, a single supply, 10-bit, 20 MSPS A/D converter that
requires only 140 mW. Using the AD8004 for level shifting and
driving, the A/D exhibits no degradation in performance com-
pared to when it is driven from a signal generator.
The analog input of the AD876 spans 2 V centered at about
2.6 V. The resistor network and bias voltages provide the level
shifting and gain required to convert the 0 V to 1 V input signal
to a 3.6 V to 1.6 V range that the AD876 wants to see.
Biasing the noninverting input of the AD8004 at 1.6 V dc forces
the inverting input to be at 1.6 V dc for linear operation of the
amplifier. When the input is at 0 V, there is 3.2 mA flowing out
of the summing junction via R1 (1.6 V/499 ). R3 has a current
of 1.2 mA flowing into the summing junction (3.6 V–1.6 V)/
1.65 k. The difference of these two currents (2 mA) must flow
through R2. This current flows toward the summing junction
and requires that the output be 2 V higher than the summing
junction or at 3.6 V.
When the input is at 1 V, there is 1.2 mA flowing into the sum-
ming junction through R3 and 1.2 mA flowing out through R1.
These currents balance and leave no current to flow through
R2. Thus the output is at the same potential as the inverting
input or 1.6 V.
The input of the AD876 has a series MOSFET switch that turns
on and off at the sampling rate. This MOSFET is connected to
a hold capacitor internal to the device. The on impedance of the
MOSFET is about 50 , while the hold capacitor is about 5 pF.
In a worst case condition, the input voltage to the AD876 will
change by a full-scale value (2 V) in one sampling cycle. When
the input MOSFET turns on, the output of the op amp will be
connected to the charged hold capacitor through the series
resistance of the MOSFET. Without any other series resistance,
the instantaneous current that flows would be 40 mA. This
would cause settling problems for the op amp.
The series 100 resistor limits the current that flows instanta-
neously after the MOSFET turns on to about 13 mA. This
resistor cannot be made too large or the high frequency perfor-
mance will be affected.
The sampling MOSFET of the AD876 is closed for only half of
each cycle or for 25 ns. Approximately seven time constants are
required for settling to 10 bits. The series 100 resistor along
with the 50 on resistance and the hold capacitor, create a
750 ps time constant. These values leave a comfortable margin
for settling. Obtaining the same results with the op amp A/D
combination as compared to driving with a signal generator
indicates that the op amp is settling fast enough.
Overall the AD8004 provides adequate buffering for the AD876
A/D converter without introducing distortion greater than that
of the A/D converter by itself.
+5V
3.6V
R3
1.65k
R2
1k
0.1F
10F
0.1F
R1
1V
VIN
499k
+3.6V
REFT
0V
50
1/4
AD8004
100
AD876
3.6V
0.1F
1.6V
REFB
1.6V
+1.6V
Figure 37. AD8004 Driving the AD876
LAYOUT CONSIDERATIONS
The specified high speed performance of the AD8004 requires
careful attention to board layout and component selection.
Table I shows the recommended component values for the
AD8004 and Figures 39–41 show the layout for the AD8004
evaluation boards (14-lead DIP and SOIC). Proper RF design
techniques and low parasitic component selection are mandatory.
REV. B
–11–
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2020  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]