M1A3P400-1PQ208YES View Datasheet(PDF) - Microsemi Corporation
Part Name
Description
Manufacturer
M1A3P400-1PQ208YES
Microsemi Corporation
M1A3P400-1PQ208YES Datasheet PDF : 220 Pages
| |||
ProASIC3 Flash Family FPGAs
Single-Ended I/O Characteristics
3.3 V LVTTL / 3.3 V LVCMOS
Low-Voltage Transistor–Transistor Logic (LVTTL) is a general-purpose standard (EIA/JESD) for 3.3 V
applications. It uses an LVTTL input buffer and push-pull output buffer.
Table 2-37 • Minimum and Maximum DC Input and Output Levels
Applicable to Advanced I/O Banks
3.3 V LVTTL /
3.3 V LVCMOS
VIL
VIH
VOL VOH IOL IOH IOSL
IOSH IIL1 IIH2
Min.
Drive Strength V
Max.
V
Min.
V
Max.
V
Max.
V
Min.
V mA mA
Max.
mA3
Max.
mA3
µA4 µA4
2 mA
–0.3
0.8
2
3.6
0.4
2.4 2 2
27
25
10 10
4 mA
–0.3 0.8
2
3.6
0.4
2.4 4 4
27
25
10 10
6 mA
–0.3 0.8
2
3.6
0.4
2.4 6 6
54
51
10 10
8 mA
–0.3 0.8
2
3.6
0.4
2.4 8 8
54
51
10 10
12 mA
–0.3 0.8
2
3.6
0.4
2.4 12 12 109
103
10 10
16 mA
–0.3 0.8
2
3.6
0.4
2.4 16 16 127
132
10 10
24 mA
–0.3 0.8
2
3.6
0.4
2.4 24 24
181
268
10 10
Notes:
1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL.
2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges
3. Currents are measured at 100°C junction temperature and maximum voltage.
4. Currents are measured at 85°C junction temperature.
5. Software default selection highlighted in gray.
Table 2-38 • Minimum and Maximum DC Input and Output Levels
Applicable to Standard Plus I/O Banks
3.3 V LVTTL /
3.3 V LVCMOS
VIL
VIH
VOL VOH IOL IOH IOSL
IOSH IIL1 IIH2
Drive Strength
Min.
V
Max.
V
Min.
V
Max.
V
Max.
V
Min.
V mA mA
Max.
mA3
Max.
mA3
µA4 µA4
2 mA
–0.3
0.8
2
3.6
0.4
2.4 2 2
27
25
10 10
4 mA
–0.3 0.8
2
3.6
0.4
2.4 4 4
27
25
10 10
6 mA
–0.3 0.8
2
3.6
0.4
2.4 6 6
54
51
10 10
8 mA
–0.3 0.8
2
3.6
0.4
2.4 8 8
54
51
10 10
12 mA
–0.3 0.8
2
3.6
0.4
2.4 12 12 109
103
10 10
16 mA
–0.3 0.8
2
3.6
0.4
2.4 16 16 109
103
10 10
Notes:
1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL.
2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges
3. Currents are measured at 100°C junction temperature and maximum voltage.
4. Currents are measured at 85°C junction temperature.
5. Software default selection highlighted in gray.
Revision 13
2- 31
|
|
Share Link: