Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits
Part Name  

AD8319ACPZ-R7-2005 View Datasheet(PDF) - Analog Devices

Part NameAD8319ACPZ-R7(2005) ADI
Analog Devices ADI
Description1 MHz to 10 GHz, 45 dB Log Detector/Controller
AD8319ACPZ-R7 Datasheet PDF : 20 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
AD8319
Parameter
f = 5.8 GHz
Input Impedance
±1 dB Dynamic Range
Maximum Input Level
Minimum Input Level
Slope1
Intercept1
Output Voltage: High Power In
Output Voltage: Low Power In
f = 8.0 GHz
Input Impedance
±1 dB Dynamic Range
Maximum Input Level
Minimum Input Level
Slope 2
Intercept2
Output Voltage: High Power In
Output Voltage: Low Power In
OUTPUT INTERFACE
Voltage Swing
Output Current Drive
Small Signal Bandwidth
Output Noise
Fall Time
Fall Time
Rise Time
Rise Time
Video Bandwidth (or Envelope
Bandwidth)
VSET INTERFACE
Nominal Input Range
Logarithmic Scale Factor
Input Resistance
TADJ INTERFACE
Input Resistance
Disable Threshold Voltage
POWER INTERFACE
Supply Voltage
Quiescent Current
vs. Temperature
Disable Current
Conditions
Min Typ
Max Unit
RTADJ = 500
110||0.05
Ω||pF
TA = +25°C
40
dB
40°C < TA < +85°C
40
dB
±1 dB error
−3
dBm
±1 dB error
−43
dBm
−22
mV/dB
15
dBm
PIN = –10 dBm
0.57
V
PIN = –40 dBm
1.25
V
RTADJ = open
28||0.79
Ω||pF
TA = +25°C
40
dB
40°C < TA < +85°C
31
dB
± 1 dB error
−1
dBm
± 1 dB error
−41
dBm
−22
mV/dB
20
dBm
PIN = –10 dBm
0.67
V
PIN = –40 dBm
1.34
V
VOUT (Pin 5)
VSET = 0 V; RFIN = open
VPOS – 0.1
V
VSET = 1.5 V; RFIN = open
10
mV
VSET = 0 V; RFIN = open
10
mA
RFIN = −10 dBm; from CLPF to VOUT
140
MHz
RF Input = 2.2 GHz, –10 dBm, fNOISE = 100 kHz, CLPF = open
90
nV/Hz
Input level = no signal to −10 dBm, 90% to 10%; CLPF = 8 pF
18
ns
Input level = no signal to −10 dBm, 90% to 10%;
CLPF = open; ROUT = 150 Ω
6
ns
Input level = –10 dBm to no signal, 10% to 90%; CLPF = 8 pF
20
ns
Input level = –10 dBm to no signal, 10% to 90%;
CLPF = open; ROUT = 150 Ω
10
ns
50
MHz
VSET (Pin 4)
RFIN = 0 dBm; measurement mode
RFIN = –40 dBm; measurement mode
RFIN = −20 dBm; controller mode; VSET = 1 V
TADJ (Pin 6)
TADJ = 0.9 V, sourcing 50 μA
TADJ = Open
VPOS (Pin 7)
−40°C TA +85°C
TADJ = VPOS
0.35
1.23
V
−45
dB/V
40
kΩ
40
kΩ
VPOS – 0.4
3.0
18 22
60
200
5.5 V
30 mA
μA/°C
μA
1 Slope and intercept are determined by calculating the best-fit line between the power levels of −40 dBm and −10 dBm at the specified input frequency.
2 Slope and intercept are determined by calculating the best-fit line between the power levels of −34 dBm and −16 dBm at 8.0 GHz.
Rev. 0 | Page 4 of 20
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]