Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

Z0107MA 데이터 시트보기 (PDF) - ON Semiconductor

부품명상세내역제조사
Z0107MA Sensitive Gate Triacs Series Silicon Bidirectional Thyristors ON-Semiconductor
ON Semiconductor ON-Semiconductor
Z0107MA Datasheet PDF : 10 Pages
1 2 3 4 5 6 7 8 9 10
Z0103MA, Z0107MA, Z0109MA
TO92 EIA RADIAL TAPE IN FAN FOLD BOX OR ON REEL
H2A
H2A
H2B
H2B
H
H4 H5
W2
T1
L1 H1
W1 W
L
T
F1
T2
F2
P2
P2
D
P1
P
Figure 12. Device Positioning on Tape
Specification
Inches
Millimeter
Symbol
Item
Min
Max
Min
Max
D
Tape Feedhole Diameter
0.1496 0.1653
3.8
4.2
D2
Component Lead Thickness Dimension
0.015
0.020
0.38
0.51
F1, F2 Component Lead Pitch
0.0945 0.110
2.4
2.8
H
Bottom of Component to Seating Plane
0.059
0.156
1.5
4.0
H1
Feedhole Location
0.3346 0.3741
8.5
9.5
H2A
Deflection Left or Right
0
0.039
0
1.0
H2B
Deflection Front or Rear
0
0.051
0
1.0
H4
Feedhole to Bottom of Component
0.7086 0.768
18
19.5
H5
Feedhole to Seating Plane
0.610
0.649
15.5
16.5
L
Defective Unit Clipped Dimension
0.3346 0.433
8.5
11
L1
Lead Wire Enclosure
0.09842
2.5
P
Feedhole Pitch
0.4921 0.5079
12.5
12.9
P1
Feedhole Center to Center Lead
0.2342 0.2658
5.95
6.75
P2
First Lead Spacing Dimension
0.1397 0.1556
3.55
3.95
T
Adhesive Tape Thickness
0.06
0.08
0.15
0.20
T1
Overall Taped Package Thickness
0.0567
1.44
T2
Carrier Strip Thickness
0.014
0.027
0.35
0.65
W
Carrier Strip Width
0.6889 0.7481
17.5
19
W1
Adhesive Tape Width
0.2165 0.2841
5.5
6.3
W2
Adhesive Tape Position
.0059 0.01968 0.15
0.5
2. Maximum alignment deviation between leads not to be greater than 0.2 mm.
3. Defective components shall be clipped from the carrier tape such that the remaining protrusion (L) does not exceed a maximum of 11 mm.
4. Component lead to tape adhesion must meet the pull test requirements.
5. Maximum noncumulative variation between tape feed holes shall not exceed 1 mm in 20 pitches.
6. Holddown tape not to extend beyond the edge(s) of carrier tape and there shall be no exposure of adhesive.
7. No more than 1 consecutive missing component is permitted.
8. A tape trailer and leader, having at least three feed holes is required before the first and after the last component.
9. Splices will not interfere with the sprocket feed holes.
http://onsemi.com
8
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]