U630H16SK35 View Datasheet(PDF) - Simtek Corporation
Part Name
Description
Manufacturer
U630H16SK35 Datasheet PDF : 15 Pages
| |||
Obsolete - Not Recommended for New Designs
U630H16
HardStore 2K x 8 nvSRAM
Features
Description
• High-performance CMOS nonvo-
latile static RAM 2048 x 8 bits
• 25, 35 and 45 ns Access Times
• 12, 20 and 25 ns Output Enable
Access Times
• Hardware STORE Initiation
(STORE Cycle Time < 10 ms)
• Automatic STORE Timing
• 106 STORE cycles to EEPROM
• 100 years data retention in
EEPROM
• Automatic RECALL on Power Up
• Hardware RECALL Initiation
(RECALL Cycle Time < 20 ms)
• Unlimited RECALL cycles from
EEPROM
• Unlimited Read and Write to
SRAM
• Single 5 V ± 10 % Operation
• Operating temperature ranges:
0to70 ×C
-40to85 ×C
-40to125 °C(only 35 ns)
• QS 9000 Quality Standard
• ESD protection > 2000 V
(MIL STD 883C M3015.7-HBM)
• RoHS compliance and Pb- free
• Packages:SOP28 (300 mil),
PDIP28 (300/600 mil)
The U630H16 has two separate
modes of operation: SRAM mode
and nonvolatile mode, determined
by the state of the NE pin.
In SRAM mode, the memory ope-
rates as an ordinary static RAM. In
nonvolatile operation, data is trans-
ferred in parallel from SRAM to
EEPROM or from EEPROM to
SRAM. In this mode SRAM
functions are disabled.
The U630H16 is a fast static RAM
(25, 35, 45 ns), with a nonvolatile
electrically erasable PROM
(EEPROM) element incorporated
in each static memory cell. The
SRAM can be read and written an
unlimited number of times, while
independent nonvolatile data resi-
des in EEPROM. Data transfers
from the SRAM to the EEPROM
(the STORE operation), or from the
EEPROM to the SRAM (the
RECALL operation) are initiated
through the state of the NE pin.
The U630H16 combines the high
performance and ease of use of a
fast SRAM with nonvolatile data
integrity.
Once a STORE cycle is initiated,
further input or output are disabled
until the cycle is completed.
Internally, RECALL is a two step
procedure. First, the SRAM data is
cleared and second, the nonvola-
tile information is transferred into
the SRAM cells.
The RECALL operation in no way
alters the data in the EEPROM
cells. The nonvolatile data can be
recalled an unlimited number of
times.
Pin Configuration
NE
n.c.
A7
A6
A5
A4
A3
A2
A1
A0
DQ0
DQ1
DQ2
VSS
1
28
2
27
3
26
4
25
5
24
6
23
7 PDIP 22
8 SOP 21
9
20
10
19
11
18
12
17
13
16
14
15
VCC
W
n.c.
A8
A9
n.c.
G
A10
E
DQ7
DQ6
DQ5
DQ4
DQ3
Top View
March 31, 2006
STK Control #ML0036
Pin Description
Signal Name
A0 - A10
DQ0 - DQ7
E
G
W
NE
VCC
VSS
Signal Description
Address Inputs
Data In/Out
Chip Enable
Output Enable
Write Enable
Nonvolatile Enable
Power Supply Voltage
Ground
1
Rev 1.0
|
|
Share Link: 