TC03VNB View Datasheet(PDF) - TelCom Semiconductor, Inc
Part Name
Description
Manufacturer
TC03VNB Datasheet PDF : 7 Pages
| |||
PRELIMINARY INFORMATION
TC02
TC03
PRECISION TEMPERATURE-
TO -VOLTAGE CONVERTERS
ABSOLUTE MAXIMUM RATINGS *
Supply Voltage ............................................................15V
Input Voltage, Any Terminal .............. – 1.0 to (VCC +0.3V)
Operating Temperature (TC02) ............. – 20°C to +125°C
Operating Temperature (TC03) ............. – 20°C to +100°C
Storage Temperature ............................ – 55°C to +150°C
Lead Temperature (Soldering, 10 sec)
SOT-23B-3 ..................................................... +260°C
TO-92-3 .......................................................... +300°C
* Static-sensitive device. Unused devices must be stored in conductive
material. Protect devices from static discharge and static fields. Stresses
above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. These are stress ratings only and functional
operation of the device at these or any other conditions above those
indicated in the operational sections of the specifications is not implied.
Exposure to Absolute Maximum Rating Conditions for extended periods
may affect device reliability.
ELECTRICAL CHARACTERISTICS : TA = – 20°C to +125°C, VCC = 5V ±5%, unless otherwise specified.
Symbol Parameter
Test Conditions
Min
Typ
Max
VCC
Supply Voltage (TC02)
VCC
Supply Voltage (TC03)
IS
Supply Current
ISRC
VOUT Output Source Current
Accuracy at Room Temperature
Accuracy at Minimum Temperature
AV
VOUTMAX
Accuracy at Maximum Temperature
(Note 2)
Nonlinearity
Line Regulation
Average Slope of Output Voltage
Maximum Output Voltage
Note 1
TA = 25°C (Note 2)
TC02: TA = – 20°C
TC03: TA = – 20°C
(Note 2)
TC02: TA = +125°C
TC03: TA = +100°C
Note 3, 4
TC02: 3.0V ≤ VCC ≤ 12V
TC03: 2.2V ≤ VCC ≤ 12V
(Note 1)
3.0
2.2
—
—
–2
–7
–7
–3
–3
– 0.8
—
—
—
—
12
—
12
40
60
—
1.0
± 0.5
+2
± 0.5
+5
± 0.5
+5
—
+3
—
+3
—
+0.8
80
—
10
—
—
VCC – 1.2
Unit
V
V
µA
mA
°C
°C
°C
°C
µV/V
mV/°C
V
Notes: 1. VOUT outputs open circuited.
2. Accuracy = Difference between calculated output voltage (10mV/°C x Device case temperature at specified temperature and power supply)
and measured output voltage expressed in °C.
3. Nonlinearity = deviation of output voltage versus temperature from the best-fit straight line over the device rated temperature range.
4. Guaranteed by design.
DETAILED DESCRIPTION
A plot of output voltage versus temperature for both the
TC02 and TC03 appears in Figure 1. The TC03 can be
used with single power supply to measure temperatures
from 0°C to 100°C. A pull-down resistor (R1 in Figure 2)
must be added from VOUT to the negative power supply for
measuring temperatures less than 0°C. The value of the
resistor must be chosen to limit the maximum current
pulled from the output to the negative supply to
– 50µA (i.e. R1 = VSS/50µA).
OUTPUT STAGE
Both the TC02 and TC03 have Class A output stages
capable of sourcing 1mA. These devices have a limited
ability to drive heavy capacitive loads. Loads of 50pF (to
ground) can be driven directly. For heavier loads, a 2kΩ (or
greater) resistor should be placed in series with the output
for decoupling. If the TC02/03 is used in a noisy electrical
environment, a 0.1µF bypass capacitor from VCC to GND is
recommended.
TC02/03-04 6/18/97
2
|
|
Share Link: 