BPB-12/4-Q48 View Datasheet(PDF) - DATEL Data Acquisition products

Part Name

Description

Manufacturer

BPB-12/4-Q48

High-Efficiency, Smaller-Package 25-40 Watt, DC/DC Converters

DATEL Data Acquisition products  

XPB Series

25-40W, DUAL OUTPUT DC/DC CONVERTERS

On/Off Control (Standard)

The On/Off Control pin (pin 5) may be used for remote on/off operation. As

shown in Figure 6, the control pin has an internal 10kΩ pull-up resistor to

approximately 10V. The converter is designed so that it is enabled when the

control pin is left open (normal mode) and disabled when the control pin is

pulled low (to less than +0.8V relative to –Input, pin 2).

Dynamic control of the on/off function is best accomplished with a mechani-

cal relay or an open-collector/open-drain drive circuit (optically isolated if

appropriate). The drive circuit should obviously be able to sink approximately

1mA when activated and withstand more than 10 Volts when deactivated.

Applying an external voltage to pin 5 when no input power is applied to the

converter can cause permanent damage to the converter. The on/off control

function, however, is designed such that the converter can be disabled (pin 5

pulled low) while input power is ramping up and then "released" once the

input has stabilized. Under these circumstances, it takes approximately

30ms for the output of the fully loaded DC/DC to ramp up and settle to within

±1% of its final value after the converter has been turned on.

Synchronization (Optional)

In critical applications employing multiple switching DC/DC converters, it may

be desirable to intentionally synchronize the switching of selected converters

(so the system noise can be reduced with notch filtering) or to purposely

desynchronize the converters (to lessen the current-carrying requirements on

intermediate dc buses). BPB DC/DC Converters have been designed so that

the On/Off Control function on pin 5 can be replaced with a Sync function. This

change has to be implemented by DATEL during the product assembly

process. Contact our Applications Engineering Group for additional details.

To synchronize the switching of multiple BPB converters configured with the

Sync function, an external clock can be applied to pin 5 of each converter.

The clock should be a TTL square wave referenced to –Input (logic high =

+2 to +5 Volts, 250µA max.; logic low = 0 to +0.8 Volts, 70µA max.) with a

maximum 1µsec "high" duration. The frequency of the synchronizing clock

should be higher than that of any individual converter. Therefore, it should be

145kHz ±5kHz.

Output Trimming

The total output voltage span, from +Output (pin 9) to –Output (pin 6) may

be trimmed ±5% via a single trimpot or fixed resistor. The trimpot should be

connected as shown in Figure 8 with its wiper connected to pin 10 (Trim). A

trimpot can also be used to determine the value of a single fixed resistor

which can be connected between pin 10 (Trim) and pin 9 (+Output) to trim

"down" the output voltages, or between pins 10 (Trim) and 6 (–Output) to

trim "up" the output voltages. Fixed resistors should be metal-film types with

absolute TCR's less than 100ppm/°C to ensure stability.

3

+INPUT

+10V

10k9

5

ON/OFF

CONTROL

2

–INPUT

Figure 6. Driving the On/Off Control Pin

+

CIN

3

+INPUT

2

–INPUT

9

+OUTPUT

8

COMMON

6

–OUTPUT

Figure 7. Using External Capacitors

to Reduce Input/Output Ripple/Noise

+

COUT

+

COUT

3

+INPUT

2

–INPUT

9

+OUTPUT

8

COMMON

10

TRIM

6

–OUTPUT

LOAD

20k9

5-10

Turns

LOAD

Figure 8. Trim Connections Using a Trimpot

Case Connection

Unlike most other DC/DC converters, BMP DC/DC's do not have their metal

case connected to one of their input pins. The "uncommitted" case is

connected to pin 4 which, depending on your system configuration, should be

connected to either +Input (pin 3) or –Input (pin 2).

®

®

INNOVATION and EXCELLENCE

ISO-9001 REGISTERED

DS-0410 12/01

DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151

Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356

Internet: www.datel.com Email: sales@datel.com

Data Sheet Fax Back: (508) 261-2857

DATEL (UK) LTD. Tadley, England Tel: (01256)-880444

DATEL S.A.R.L. Montigny Le Bretonneux, France Tel: 01-34-60-01-01

DATEL GmbH München, Germany Tel: 89-544334-0

DATEL KK Tokyo, Japan Tel: 3-3779-1031, Osaka Tel: 6-6354-2025

DATEL makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions

contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. The DATEL logo is a registered DATEL,

Inc. trademark.

6

Share Link: