Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

HI-8282C View Datasheet(PDF) - Unspecified

Part NameDescriptionManufacturer
HI-8282C ARINC 429 SERIAL TRANSMITTER AND DUAL RECEIVER Unspecified
Unspecified 
HI-8282C Datasheet PDF : 13 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
HI-8282
September 2006 ARINC 429 SERIAL TRANSMITTER AND DUAL RECEIVER
GENERAL DESCRIPTION
The HI-8282 is a silicon gate CMOS device for interfacing
the ARINC 429 serial data bus to a 16-bit parallel data bus.
Two receivers and an independent transmitter are
provided. The receiver input circuitry and logic are
designed to meet the ARINC 429 specifications for loading,
level detection, timing, and protocol. The transmitter
section provides the ARINC 429 communication protocol.
An external line driver such as the Holt HI-8585 or HI-3182
is required to translate the 5 volt logic outputs to ARINC 429
drive levels.
The 16-bit parallel data bus exchanges the 32-bit ARINC
data word in two steps when either loading the transmitter
or interrogating the receivers. The data bus interfaces with
CMOS and TTL.
Timing of all the circuitry begins with the master clock input,
CLK. For ARINC 429 applications, the master clock
frequency is 1 MHz.
Each independent receiver monitors the data stream with a
sampling rate 10 times the data rate. The sampling rate is
software selectable at either 1MHz or 125KHz. The results
of a parity check are available as the 32nd ARINC bit. The
HI-8282 examines the null and data timings and will reject
erroneous patterns. For example, with a 125 KHz clock
selection, the data frequency must be between 10.4 KHz
and 15.6 KHz.
The transmitter has a First In, First Out (FIFO) memory to
store 8 ARINC words for transmission. The data rate of the
transmitter is software selectable by dividing the master
clock, CLK, by either 10 or 80. The master clock is used to
set the timing of the ARINC transmission within the required
resolution.
APPLICATIONS
! Avionics data communication
! Serial to parallel conversion
! Parallel to serial conversion
FEATURES
! ARINC specification 429 compliant
! 16-Bit parallel data bus
! Direct receiver interface to ARINC bus
! Timing control 10 times the data rate
! Selectable data clocks
! Receiver error rejection per ARINC
specification 429
! Automatic transmitter data timing
! Self test mode
! Parity functions
! Low power, single 5 volt supply
! Industrial & full military temperature ranges
! DSCC SMD part number
PIN CONFIGURATION (Top View)
Vcc 1
(REC. 1 INPUT) 429DI1(A) 2
(REC.1 INPUT) 429DI1(B) 3
(REC. 2 INPUT) 429DI2(A) 4
(REC. 2 INPUT) 429DI2(B) 5
(REC.1 DATA FLAG) D/R1 6
(REC.2 DATA FLAG) D/R2 7
(REC. BYTE SELECT) SEL 8
(REC. 1 OUTPUT ENABLE) EN1 9
(REC. 2 OUTPUT ENABLE) EN2 10
BD15 11
BD14 12
BD13 13
BD12 14
BD11 15
BD10 16
BD09 17
BD08 18
BD07 19
BD06 20
40 NC
39 MR (MASTER RESET)
38 TX CLK (XMIT CLOCK OUT)
37 CLK (MASTER CLK IN)
36 NC
35 NC
34 CWSTR (CONTROL WORD STROBE)
33 ENTX (ENABLE XMIT)
32 429DO (XMIT DATA)
31 429DO (XMIT DATA)
30 TX/R (XMIT READY FLAG)
29 PL2 (XMIT BYTE 2 LE)
28 PL1 (XMIT BYTE 1 LE)
27 BD00
26 BD01
25 BD02
24 BD03
23 BD04
22 BD05
21 GND
HI-8282C / CT / CM-01 / CM-03
SMD # 5962-8688002QA
40-Pin Ceramic Side-Brazed DIP
(See page 10 for additional Package Pin Configurations)
(DS8282 Rev. E)
HOLT INTEGRATED CIRCUITS
www.holtic.com
09/06
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]