Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

A29002UL-120 View Datasheet(PDF) - AMIC Technology

Part NameDescriptionManufacturer
A29002UL-120 256K X 8 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory AMIC
AMIC Technology AMIC
A29002UL-120 Datasheet PDF : 32 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
A29002/A290021 Series
256K X 8 Bit CMOS 5.0 Volt-only,
Boot Sector Flash Memory
Features
n 5.0V ± 10% for read and write operations
n Access times:
- 55/70/90/120/150 (max.)
n Current:
- 20 mA typical active read current
- 30 mA typical program/erase current
- 1 µA typical CMOS standby
n Flexible sector architecture
- 16 Kbyte/ 8 KbyteX2/ 32 Kbyte/ 64 KbyteX3 sectors
- Any combination of sectors can be erased
- Supports full chip erase
- Sector protection:
A hardware method of protecting sectors to prevent
any inadvertent program or erase operations within
that sector
n Top or bottom boot block configurations available
n Embedded Erase Algorithms
- Embedded Erase algorithm will automatically erase
the entire chip or any combination of designated
sectors and verify the erased sectors
- Embedded Program algorithm automatically writes
and verifies bytes at specified addresses
n Typical 100,000 program/erase cycles per sector
n 20-year data retention at 125°C
- Reliable operation for the life of the system
n Compatible with JEDEC-standards
- Pinout and software compatible with single-power-
supply Flash memory standard
- Superior inadvertent write protection
n Data Polling and toggle bits
- Provides a software method of detecting completion
of program or erase operations
n Erase Suspend/Erase Resume
- Suspends a sector erase operation to read data
from, or program data to, a non-erasing sector, then
resumes the erase operation
n Hardware reset pin (RESET )
- Hardware method to reset the device to reading array
data (not available on A290021)
n Package options
- 32-pin P-DIP, PLCC, or TSOP (Forward type)
General Description
The A29002 is a 5.0 volt-only Flash memory organized as
262,144 bytes of 8 bits each. The A29002 offers the RESET
function, but it is not available on A290021. The 256 Kbytes
of data are further divided into seven sectors for flexible
sector erase capability. The 8 bits of data appear on I/O0 -
I/O7 while the addresses are input on A0 to A17. The A29002
is offered in 32-pin PLCC, TSOP, and PDIP packages. This
device is designed to be programmed in-system with the
standard system 5.0 volt VCC supply. Additional 12.0 volt
VPP is not required for in-system write or erase operations.
However, the A29002 can also be programmed in standard
EPROM programmers.
The A29002 has the first toggle bit, I/O6, which indicates
whether an Embedded Program or Erase is in progress, or it
is in the Erase Suspend. Besides the I/O6 toggle bit, the
A29002 has a second toggle bit, I/O2, to indicate whether the
addressed sector is being selected for erase. The A29002
also offers the ability to program in the Erase Suspend mode.
The standard A29002 offers access times of 55, 70, 90, 120,
and 150 ns, allowing high-speed microprocessors to operate
without wait states. To eliminate bus contention the device
has separate chip enable ( CE ), write enable ( WE ) and
output enable ( OE ) controls.
The device requires only a single 5.0 volt power supply for both
read and write functions. Internally generated and regulated
voltages are provided for the program and erase operations.
The A29002 is entirely software command set compatible with
the JEDEC single-power-supply Flash standard. Commands
are written to the command register using standard
microprocessor write timings. Register contents serve as input
to an internal state-machine that controls the erase and
programming circuitry. Write cycles also internally latch
addresses and data needed for the programming and erase
operations. Reading data out of the device is similar to reading
from other Flash or EPROM devices.
Device programming occurs by writing the proper program
command sequence. This initiates the Embedded Program
algorithm - an internal algorithm that automatically times the
program pulse widths and verifies proper program margin.
Device erasure occurs by executing the proper erase command
sequence. This initiates the Embedded Erase algorithm - an
internal algorithm that automatically preprograms the array (if it
is not already programmed) before executing the erase
operation. During erase, the device automatically times the
erase pulse widths and verifies proper erase margin.
(February, 2002, Version 1.0)
1
AMIC Technology, Inc.
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]