74LVT16240A View Datasheet(PDF) - Philips Electronics
Part Name
Description
Manufacturer
74LVT16240A Datasheet PDF : 10 Pages
| |||
Philips Semiconductors
3.3V 16-bit inverting buffer/driver (3-State)
Product specification
74LVT16240A
DC ELECTRICAL CHARACTERISTICS
SYMBOL
PARAMETER
VIK
Input clamp voltage
VOH High-level output voltage
VOL Low-level output voltage
II
Input leakage current
IOFF Output off current
IHOLD Bus Hold current A inputs6
IEX
IPU/PD
IOZH
IOZL
ICCH
ICCL
ICCZ
∆ICC
Current into an output in the
High state when VO > VCC
Power up/down 3-State output
current3
3-State output High current
3-State output Low current
Quiescent supply current
Additional supply current per
input pin2
TEST CONDITIONS
VCC = 2.7V; IIK = -18mA
VCC = 2.7 to 3.6V; IOH = -100µA
VCC = 2.7V; IOH = -8mA
VCC = 3.0V; IOH = -32mA
VCC = 2.7V; IOL = 100µA
VCC = 2.7V; IOL = 24mA
VCC = 3.0V; IOL = 16mA
VCC = 3.0V; IOL = 32mA
VCC = 3.0V; IOL = 64mA
VCC = 3.6V; VI = VCC or GND
VCC = 0 or 3.6V; VI = 5.5V
VCC = 3.6V; VI = VCC
VCC = 3.6V; VI = 0
VCC = 0V; VI or VO = 0 to 4.5V
VCC = 3V; VI = 0.8V
VCC = 3V; VI = 2.0V
VCC = 0V to 3.6V; VCC = 3.6V
Control pins
Data pins4
VO = 5.5V; VCC = 3.0V
VCC ≤ 1.2V; VO = 0.5V to VCC; VI = GND or VCC
OE/OE = Don’t care
VCC = 3.6V; VO = 3.0V; VI = VIL or VIH
VCC = 3.6V; VO = 0.5V; VI = VIL or VIH
VCC = 3.6V; Outputs High, VI = GND or VCC, IO = 0
VCC = 3.6V; Outputs Low, VI = GND or VCC, IO = 0
VCC = 3.6V; Outputs Disabled; VI = GND or VCC, IO = 05
VCC = 3V to 3.6V; One input at VCC-0.6V,
Other inputs at VCC or GND
LIMITS
Temp = -40°C to +85°C
MIN
TYP1 MAX
–0.85 1.2
VCC-0.2 VCC
2.4
2.5
2.0
2.3
0.07 0.2
0.03 0.5
0.25 0.4
0.30 0.5
0.40 0.55
0.1 ±1.0
0.4
10
0.1
1
-0.4 -5
0.1 ±100
75
135
-75
-135
±500
50 125
1 ±100
0.5
5
0.5
-5
0.07 0.12
4.0 6.0
0.07 0.12
0.1 0.20
UNIT
V
V
V
µA
µA
µA
µA
µA
µA
mA
mA
NOTES:
1. All typical values are at VCC = 3.3V and Tamb = 25°C.
2. This is the increase in supply current for each input at the specified voltage level other than VCC or GND
3. This parameter is valid for any VCC between 0V and 1.2V with a transition time of up to 10msec. From VCC = 1.2V to VCC = 3.3V ± 0.3V a
transition time of 100µsec is permitted. This parameter is valid for Tamb = 25°C only.
4. Unused pins at VCC or GND.
5. ICCZ is measured with outputs pulled to VCC or GND.
6. This is the bus hold overdrive current required to force the input to the opposite logic state.
AC CHARACTERISTICS
GND = 0V; tR = tF = 2.5ns; CL = 50pF; RL = 500Ω; Tamb = -40°C to +85°C.
SYMBOL
PARAMETER
WAVEFORM
tPLH
tPHL
tPZH
tPZL
tPHZ
tPLZ
Propagation delay
nAx to nYx
Output enable time
to High and Low level
Output disable time
from High and Low Level
NOTE:
1. All typical values are at VCC = 3.3V and Tamb = 25°C.
1998 Feb 19
1
2
2
5
LIMITS
VCC = 3.3V ±0.3V
MIN
TYP1
MAX
0.5
1.8
3.2
0.5
2.0
3.2
1.0
2.3
4.0
1.0
2.1
4.4
1.0
3.2
4.5
1.0
3.0
4.4
VCC = 2.7V
MAX
4.0
4.0
5.0
4.8
5.0
4.8
UNIT
ns
ns
ns
|
|
Share Link: 