Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

TXD2-1.5V View Datasheet(PDF) - Panasonic Corporation

Part NameDescriptionManufacturer
TXD2-1.5V High breakdown voltage type is available (1.5 kV between open contacts) TX-D RELAYS Panasonic
Panasonic Corporation Panasonic
TXD2-1.5V Datasheet PDF : 12 Pages
First Prev 11 12
TX-D
NOTES
1. Packing style
1) Tube packing
The relay is packed in a tube with the
relay orientation mark on the left side, as
shown in the figure below.
Orientation (indicates PIN No.1) stripe
Stopper (gray)
Stopper (green)
2) Tape and reel packing (surface-mount
terminal type)
(1) Tape dimensions
(i) SA type
mm inch
Relay polarity
(Z type)
bar
1.5
+0.1
0
dia.
.059
+.004
0
dia.
2.0
.079
4.0
.157
1.75
.069
C
A
B 11.5
.453 15.5
.610
0.4
.016
TX-D relays
16.0
D
10.0 .394
.630
Tape coming out direction
24.0 ±0.3
.945 ±.012 9.2±0.2
.362±.008
(ii) SL type
mm inch
Relay polarity bar
(Z type)
1.5
+0.1
0
dia.
.059
+.004
0
dia.
2.0
.079
4.0
.157
TX-D relays
16.0
.630 10.0
.394
Tape coming out direction
(iii) SS type
1.75 0.4
.069 .016
11.5
.453
15.5
.610
24.0 ±0.3
.945 ±.012 10.8±0.2
.425±.008
mm inch
Relay polarity bar
(Z type)
1.5
.059
+0.1
0
dia.
+.004
0
dia.
2.0
.079
4.0
.157
1.75
.069
0.4
.016
TX-D relays
11.5
.453
15.5
.610
16.0
8.0 24.0 ±0.3
.630
.315
.945
10.8 ±.012
±0.2
.425±.008
Tape coming out direction
(2) Dimensions of plastic reel
21±0.6 dia.
.827±.024 dia.
mm inch
2.0±0.5
.079±.020
80±1 dia.
3.150±.039 dia.
13±0.5 dia.
.512±.020 dia.
24.4+02
.961+0.079
380±2 dia.
14.961±.079 dia.
2.0±0.2
.079±.008
3) Ambient temperature when
transporting and during storage with the
product in its original packaging:
–40 to +70°C –40 to +158°F
2. Automatic insertion
To maintain the internal function of the
relay, the chucking pressure should not
exceed the values below.
C
A
B
Chucking pressure in the direction A:
4.9 N {500gf} or less
Chucking pressure in the direction B:
9.8 N {1 kgf} or less
Chucking pressure in the direction C:
9.8 N {1 kgf} or less
Please chuck the portion.
Avoid chucking the center of the relay.
In addition, excessive chucking pressure
to the pinpoint of the relay should be
avoided.
3. M.B.B. type
A small OFF time may be generated by
the contact bounce during contact
switching. Check the actual circuit
carefully.
If the relay is dropped accidentally, check
the appearance and characteristics
including M.B.B. time before use.
Min. 10µs
500
5V DC
Measuring condition of M.B.B. time
For general cautions for use,
please refer to the “Cautions for
use of Signal Relays” or “General
Application Guidelines”.
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]