AD7708BRUZ View Datasheet(PDF) - Analog Devices

Part Name

Description

Manufacturer

AD7708BRUZ

8-/10-Channel, Low Voltage, Low Power, Σ-∆ ADCs

Analog Devices 

AD7708/AD7718

Bipolar Mode

With an analog input voltage of (–1.024 VREF/GAIN), the output code is 0000 Hex using the AD7708 and 000000H using the AD7718.

With an analog input voltage of 0 V, the output code is 8000Hex for the AD7708 and 800000Hex for the AD7718. With an analog

input voltage of (+1.024 VREF/GAIN), the output code is FFFF Hex for the AD7708 and FFFFFF Hex for the AD7718. Note the

analog inputs are pseudo bipolar inputs and the analog input voltage must remain within the common-mode input range at all times.

The output code for any analog input voltage can be represented as follows:

Code = 2N–1 × [(AIN × GAIN/1.024 × VREF) + 1]

where

AIN is the analog input voltage,

N = 16 for the AD7708, and

N = 24 for the AD7718.

ADC Offset Calibration Coefficient Registers (OF0): (A3, A2, A1, A0 = 0, 1, 0, 1; Power-On-Reset = 8000(00)Hex)

The offset calibration registers are 16-bit registers on the AD7708 and 24-bit registers on the AD7718. These registers hold the offset

calibration coefficient for the ADC. The power-on-reset value of the internal zero-scale calibration coefficient registers is 8000(00).

There are five offset registers available, one for each of the fully differential input channels. Calibration register pairs are shared when

operating in pseudo-differential input mode. However, these bytes will be automatically overwritten if an internal or system zero-scale

calibration is initiated by the user via MD2–MD0 bits in the MODE register. The channel bits, in association with the communication

register address for the OF0 register, allow access to this register. This register is a read/write register. The calibration register can

only be written to if the ADC is inactive (MD bits in the mode register = 000 or 001). Reading of the calibration register does not

clear the RDY bit.

ADC Gain Calibration Coefficient Register (GNO): (A3, A2, A1, A0 = 0, 1, 1, 0; Power-On-Reset = 5XXX(X5) Hex)

The gain calibration registers are 16-bit registers on the AD7708 and 24-bit registers on the AD7718. These registers are configured

at power-on with factory-calculated internal full-scale calibration coefficients. There are five full-scale registers available, one for each

of the fully differential input channels. Calibration register pairs are shared when operating in pseudo-differential input mode. Every

device will have different default coefficients. However, these bytes will be automatically overwritten if an internal or system full-scale

calibration is initiated by the user via MD2–MD0 bits in the MODE register. The channel bits, in association with the communication

register address, allow access to the data contained in the GN0 register. This is a read/write register. The calibration registers can

only be written to if the ADC is inactive (MD bits in the mode register = 000 or 001). Reading of the calibration registers does not

clear the RDY bit. A calibration (self or system) is required when operating with chop mode disabled.

ID Register (ID): (A3, A2, A1, A0 = 1, 1, 1, 1; Power-On-Reset = 4X Hex (AD7718) and 5X Hex (AD7708)

This register is a read only 8-bit register. The contents are used to determine the die revision of the silicon. Table XX indicates the

bit locations for the AD7708.

Table XX. ID Register Bit Designation

ID7

ID6

ID5

ID4

ID3

ID2

ID1

ID0

0

1

0

0/1

X

X

X

X

User Nonprogrammable Test Registers

The AD7708 and AD7718 contain two test registers. The bits in these test registers control the test modes of these ADCs which are

used for the testing of the device. The user is advised not to change the contents of these registers.

REV. 0

–31–

Share Link: