AD7840JN View Datasheet(PDF) - Analog Devices

Part Name

Description

Manufacturer

AD7840JN

LC2MOS Complete 14-Bit DAC

Analog Devices 

AD7840

OP AMP SECTION

The output from the voltage mode DAC is buffered by a

noninverting amplifier. Internal scaling resistors on the AD7840

configure an output voltage range of ± 3 V for an input reference

voltage of +3 V. The arrangement of these resistors around the

output op amp is as shown in Figure 1. The buffer amplifier is

capable of developing ± 3 V across a 2 kΩ and 100 pF load to

ground and can produce 6 V peak-to-peak sine wave signals to a

frequency of 20 kHz. The output is updated on the falling edge

of the LDAC input. The amplifier settles to within 1/2 LSB of

its final value in typically less than 2.5 µs.

The small signal (200 mV p-p) bandwidth of the output buffer

amplifier is typically 1 MHz. The output noise from the ampli-

fier is low with a figure of 30 nV/√Hz at a frequency of 1 kHz.

The broadband noise from the amplifier exhibits a typical peak-

to-peak figure of 150 µV for a 1 MHz output bandwidth. Figure

4 shows a typical plot of noise spectral density versus frequency

for the output buffer amplifier and for the on-chip reference.

Figure 4. Noise Spectral Density vs. Frequency

TRANSFER FUNCTION

The basic circuit configuration for the AD7840 is shown in Fig-

ure 5. Table II shows the ideal input code to output voltage re-

lationship for this configuration. Input coding to the DAC is 2s

complement with 1 LSB = FS/16,384 = 6 V/16,384 = 366 µV.

Table II. Ideal Input/Output Code Table

DAC Latch Contents

MSB

LSB

01111111111111

01111111111110

00000000000001

00000000000000

11111111111111

10000000000001

10000000000000

Analog Output, VOUT*

+2.999634 V

+2.999268 V

+0.000366 V

0V

–0.000366 V

–2.999634 V

–3 V

*Assuming REF IN = +3 V.

The output voltage can be expressed in terms of the input code,

N, using the following expression:

V OUT

=

2 × N × REFIN

16384

− 8192

≤N

≤ +8191

INTERFACE LOGIC INFORMATION

The AD7840 contains two 14-bit latches, an input latch and a

DAC latch. Data can be loaded to the input latch in one of two

basic interface formats. The first is a parallel 14-bit wide data

word; the second is a serial interface where 16 bits of data are

serially clocked into the input latch. In the parallel mode, CS

and WR control the loading of data. When the serial data format

is selected, data is loaded using the SCLK, SYNC and SDATA

serial inputs. Data is transferred from the input latch to the

DAC latch under control of the LDAC signal. Only the data in

the DAC latch determines the analog output of the AD7840.

Parallel Data Format

Table III shows the truth table for AD7840 parallel mode op-

eration. The AD7840 normally operates with a parallel input

data format. In this case, all 14 bits of data (appearing on data

inputs D13 (MSB) through D0 (LSB)) are loaded to the

AD7840 input latch at the same time. CS and WR control the

loading of this data. These control signals are level-triggered;

therefore, the input latch can be made transparent by holding

both signals at a logic low level. Input data is latched into the in-

put latch on the rising edge of CS or WR.

The DAC latch is also level triggered. The DAC output is nor-

mally updated on the falling edge of the LDAC signal. However,

both latches cannot become transparent at the same time.

Therefore, if LDAC is hardwired low, the part operates as fol-

lows; with LDAC low and CS and WR high, the DAC latch is

transparent. When CS and WR go low (with LDAC still low),

the input latch becomes transparent but the DAC latch is dis-

abled. When CS or WR return high, the input latch is locked

out and the DAC latch becomes transparent again and the DAC

output is updated. The write cycle timing diagram for parallel

data is shown in Figure 6. Figure 7 shows the simplified parallel

input control logic for the AD7840.

Figure 5. AD7840 Basic Connection Diagram

–6–

REV. B

Share Link: