Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits
Part Name  

GE28F400B3BC90 View Datasheet(PDF) - Intel

Part NameGE28F400B3BC90 Intel
Intel Intel
Description3 Volt Advanced Boot Block Flash Memory
GE28F400B3BC90 Datasheet PDF : 58 Pages
First Prev 11 12 13 14 15 16 17 18 19 20 Next Last
28F004/400B3, 28F008/800B3, 28F016/160B3, 28F320B3, 28F640B3
Table 7. Status Register Bit Definition
WSMS
ESS
ES
PS
VPPS
PSS
BLS
R
7
6
5
4
3
2
1
0
SR.7 = WRITE STATE MACHINE STATUS (WSMS)
1 = Ready
0 = Busy
SR.6 = ERASE-SUSPEND STATUS (ESS)
1 = Erase Suspended
0 = Erase In Progress/Completed
SR.5 = ERASE STATUS (ES)
1 = Error In Block Erasure
0 = Successful Block Erase
SR.4 = PROGRAM STATUS (PS)
1 = Error in Word Program
0 = Successful Word Program
SR.3 = VPP STATUS (VPPS)
1 = VPP Low Detect, Operation Abort
0 = VPP OK
SR.2 = PROGRAM SUSPEND STATUS (PSS)
1 = Program Suspended
0 = Program in Progress/Completed
SR.1 = BLOCK LOCK STATUS
1 = Program/Erase attempted on locked block;
Operation aborted
0 = No operation to locked blocks
SR.0 = RESERVED FOR FUTURE ENHANCEMENTS (R)
NOTES:
Check Write State Machine bit first to determine word program
or block erase completion, before checking program or erase
status bits.
When erase suspend is issued, WSM halts execution and sets
both WSMS and ESS bits to “1.” ESS bit remains set at “1” until
an Erase Resume command is issued.
When this bit is set to “1,” WSM has applied the max. number
of erase pulses to the block and is still unable to verify
successful block erasure.
When this bit is set to “1,” WSM has attempted but failed to
program a word.
The VPP status bit does not provide continuous indication of
VPP level. The WSM interrogates VPP level only after the
Program or Erase command sequences have been entered,
and informs the system if VPP has not been switched on. The
VPP is also checked before the operation is verified by the
WSM. The VPP status bit is not guaranteed to report accurate
feedback between VPPLK max and VPP1 min or between VPP1
max and VPP4 min.
When program suspend is issued, WSM halts execution and
sets both WSMS and PSS bits to “1.” PSS bit remains set to “1”
until a Program Resume command is issued.
If a program or erase operation is attempted to one of the
locked blocks, this bit is set by the WSM. The operation
specified is aborted and the device is returned to read status
mode.
This bit is reserved for future use and should be masked out
when polling the status register.
NOTE: A Command Sequence Error is indicated when both SR.4, SR.5 and SR.7 are set.
3.3
3.3.1
Block Locking
The 3 Volt Advanced Boot Block flash memory architecture features two hardware-lockable
parameter blocks.
WP# = VIL for Block Locking
The lockable blocks are locked when WP# = VIL; any program or erase operation to a locked block
will result in an error, which will be reflected in the status register. For top configuration, the top
two parameter blocks (blocks #133 and #134 for the 64 Mbit, #69 and #70 for the 32 Mbit, blocks
#37 and #38 for the 16 Mbit, blocks #21 and #22 for the 8 Mbit, blocks #13 and #14 for the 4 Mbit)
are lockable. For the bottom configuration, the bottom two parameter blocks (blocks #0 and #1 for
4 /8 /16 /32/64 Mbit) are lockable. Unlocked blocks can be programmed or erased normally (unless
VPP is below VPPLK).
14
3UHOLPLQDU\
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]