MAX976ESA View Datasheet(PDF) - Maxim Integrated

Part Name

Description

Manufacturer

MAX976ESA

Single/Dual/Quad, SOT23, Single-Supply, High-Speed, Low-Power Comparators

Maxim Integrated 

MAX976/MAX978/MAX998

Single/Dual/Quad, SOT23, Single-Supply,

High-Speed, Low-Power Comparators

Hysteresis

High-speed comparators can oscillate in the linear

operating region because of noise or undesired para-

sitic feedback. This tends to occur when the voltage on

one input is equal to or very close to the voltage on the

other input. The MAX976/MAX978/MAX998 have inter-

nal hysteresis to counter parasitic effects and noise.

The hysteresis in a comparator creates two trip points:

one for the rising input voltage and one for the falling

input voltage (Figure 1). The difference between the trip

points is the hysteresis. When the comparator input

voltages are equal, the hysteresis effectively causes

one comparator input voltage to move quickly past the

other, taking the input out of the region where oscilla-

tion occurs.

Figure 1 illustrates the case where IN- has a fixed volt-

age applied and IN+ is varied. If the inputs were

reversed, the figure would be the same, except with an

inverted output.

Input-Stage Circuitry

The MAX976/MAX978/MAX998 input common-mode

voltage range is from -0.2V to (VCC - 1.2V). The voltage

range for each comparator input extends to both VCC

and GND. The output remains in the correct logic state

while one or both of the inputs are within the common-

mode range. If both input levels are out of the common-

mode range, input-stage current saturation occurs, and

the output becomes unpredictable.

Shutdown Mode

The MAX998 features a low-power shutdown mode,

which is activated by forcing SHDN low. Shutdown

mode reduces the supply current to 1nA (typical), dis-

ables the comparator, and places the output in a high-

impedance state. Drive SHDN high to enable the

comparator. Do not leave SHDN unconnected. Since it

is a high-impedance input, leaving SHDN unconnected

could result in indeterminate logic levels, adversely

VHYST

VTRIP+

VIN+

VTRIP-

VOS = VTRIP+ + VTRIP-

2

VIN- = 0

COMPARATOR

VOH

OUTPUT

VOL

Figure 1. Input and Output Waveforms, Noninverting Input

Varied

6

affecting comparator operation. Likewise, do not three-

state SHDN. Due to the output leakage currents of

three-state devices and the small internal current for

SHDN, three-stating this pin could also result in indeter-

minate logic levels.

The maximum input voltage for SHDN is 6V, referred to

GND, and is not limited by VCC. This allows the use of

5V logic to drive SHDN while VCC operates at a lower

voltage, such as 3V. The logic threshold limits for

SHDN are proportional to VCC (see Electrical

Characteristics).

_____________Applications Information

Circuit Layout and Bypassing

The MAX976/MAX978/MAX998 have a high-gain band-

width and require careful board layout. We recommend

the following design guidelines:

1) Use a printed circuit board with an unbroken, low-

inductance ground plane. Surface-mount compo-

nents are recommended.

2) Place a decoupling capacitor (a 0.1µF ceramic

capacitor is a good choice) between VCC and

ground as close to the pins as possible.

3) Keep lead lengths short on the inputs and outputs

to avoid unwanted parasitic feedback around the

comparators.

4) Solder the devices directly to the printed circuit

board instead of using a socket.

5) Minimize input impedance.

6) For slowly varying inputs, use a small capacitor

(~1000pF) across the inputs to improve stability.

Additional Hysteresis

Generate additional hysteresis with three resistors

using positive feedback, as shown in Figure 2. This

positive feedback method slows the hysteresis

response time. Calculate resistor values as follows:

1) Select R3. The leakage current of IN+ is typically

75nA, so the current through R3 should be at least

1.0µA to minimize errors caused by leakage current.

The current through R3 at the trip point is (VREF -

VOUT) / R3. Consider the two possible output states

when solving for R3. The two formulas are:

R3 = VREF/1.0µA

or

R3 = (VCC - VREF)/1.0µA

Use the smaller of the two resulting resistor values.

For example, if VREF = 1.2V and VCC = 5.0V, the two

resistor values are 1.2MΩ and 3.8MΩ. Choose a

standard value for R3 of 1.2MΩ.

Maxim Integrated

Share Link: